Breaker keeps tripping: overload, short or ground fault
A breaker that keeps tripping is doing its job: it cuts power because too much current is flowing or current is going somewhere it should not. The three usual causes are an overloaded circuit, a short circuit, and a ground fault. If you notice heat, scorch marks or a burning smell, or the breaker will not reset, stop and call a licensed electrician.
Three causes, three patterns
-Overload. It trips after things have been running a while, often when a space heater, hair dryer, microwave or window AC is on the same circuit as other devices. The wiring is fine; the circuit is asked to carry more than it is rated for.
- Short circuit. It trips instantly, often the moment you plug something in or flip a switch. A hot wire is touching a neutral wire, inside a device, a cord or the wall. You may hear a pop or see a dark mark at an outlet.
- Ground fault. A hot wire is touching a ground path or water. These are most common in kitchens, bathrooms, laundry rooms, garages, basements and outdoors, and they often trip a GFCI outlet or breaker.
Resetting a breaker the safe way
Stand on a dry floor with dry hands. Open the panel door, but do not remove the inner cover; the parts behind it stay live. A tripped breaker usually rests in the middle, or shows an orange or red flag. Push the handle firmly to Off, then back to On.
Reset it once. If it trips again right away, leave it off and work through the test below before trying again.
Test the circuit by unplugging
- Clear the circuit. Turn off the lights and unplug everything on the outlets that lost power, then reset the breaker.
- Trips with nothing plugged in. The fault is in the wiring, an outlet or a hardwired fixture. That is a job for an electrician.
- Holds when empty. Plug devices back in one at a time and switch each one on. When the breaker trips, the last item is the likely cause. Try that item on a different circuit; if it trips there too, the device is the problem.
- Trips only with everything on. No single item causes it, so you have an overload. Move the heaviest loads, such as space heaters, to other circuits.
GFCI and AFCI protection
GFCI devices look for current leaking to ground, which protects you from shock. You will find them as outlets with Test and Reset buttons, or as breakers with a test button. One GFCI outlet often protects other outlets farther down the same circuit, so a dead bathroom outlet may be reset from a GFCI in another bathroom or the garage. Press Test, then Reset, about once a month.
AFCI breakers look for arcing, the small sparks from a damaged cord, a loose connection or a nail through a cable. They also have a test button. An AFCI that trips now and then can point to a worn cord or a loose wire in a box. Some breakers combine both kinds of protection.
Signs that mean stop and call
Leave the breaker off and call a licensed electrician if you notice any of these:
- The breaker or panel cover feels warm or hot.
- Scorch marks, melted plastic or discoloring at an outlet, switch or the panel.
- A burning or hot plastic smell.
- Buzzing or crackling from the panel or a wall.
- A breaker that will not reset, or trips the instant it is reset with nothing plugged in.
- Lights that flicker or dim when appliances start.
If you see smoke or flames, get everyone out and call 911 from outside.
Never swap in a bigger breaker
Each breaker is sized to match the wire it protects. Putting a 20 amp breaker on wire meant for 15 amps lets the wire carry more current than it can handle, and the wire can overheat inside the wall long before the breaker reacts. Taping a breaker on or holding it in place is just as unsafe. The fix for a circuit that is often overloaded is a new circuit, installed by an electrician.
In Maryland, all electrical work must be done by a licensed Master, Journeyperson or Apprentice Electrician, according to the Maryland State Board of Electricians, which offers a license search on its website.
Questions people ask
Is it safe to keep resetting a breaker that trips?
No. One reset is fine. A breaker that trips again is telling you about an overload or a fault, and repeated resets put strain on the wiring.
Why does my breaker trip when I use a space heater?
A space heater draws a lot of current, so it often overloads a circuit that is already powering other things. Run it on a circuit with little else plugged in, and plug it straight into the wall.
Can a breaker wear out?
Yes. A breaker that trips under a light load, feels warm or will not stay on may be failing. An electrician can test and replace it with the correct size.
Can smart devices show what is tripping my breaker?
Smart plugs that track energy use and some whole home energy monitors show which devices draw the most power and when a circuit loses power. Strech, the home operating system, is designed to pull that kind of signal together and point you to a vetted local pro.
Related
Updated November 18, 2026 · Strech Inc., Montgomery County, Maryland