Furnace not working: getting your heat back
A furnace that will not heat is often stopped by something simple: a thermostat setting, a clogged filter, a service switch turned off, or a loose door panel. The blinking light on the control board usually tells you which part is unhappy. If you smell gas, leave the home and call your gas company or 911 from outside, and if a carbon monoxide alarm sounds, get everyone out into fresh air.
Safety comes before any check
- Gas smell. Rotten egg odor near the furnace or anywhere in the house means leave now. Do not flip lights or switches on or off, and do not try to relight anything. Call your gas company or 911 once you are outside.
- Carbon monoxide alarm. Gas and oil furnaces can release carbon monoxide, a gas you cannot see or smell. If the alarm goes off, take everyone outside to fresh air and call 911 from there. Do not go back in until responders say it is safe.
- Know the symptoms. Headache, dizziness, nausea, tiredness and shortness of breath, especially in several people at once, can mean carbon monoxide. They are easy to mistake for the flu.
The U.S. Consumer Product Safety Commission advises a carbon monoxide alarm on every level of the home and outside sleeping areas.
Thermostat and filter
Set the thermostat to Heat and raise it a few degrees above the room temperature. Swap the batteries if the screen is blank or faint. On many systems the thermostat runs on power from the furnace, so a dark screen with fresh batteries points you to the furnace.
Next, slide out the filter. A filter packed with dust restricts air, the heat exchanger runs hot, and a safety limit switch shuts the burners off. The furnace may start, run a few minutes, then stop, over and over. A clean filter of the size printed on the old frame often ends that cycle.
The furnace switch, breaker and door panel
Most furnaces have a service switch that looks like an ordinary light switch, on the unit or a nearby wall. People turn it off by mistake, thinking it controls a light. Make sure it is on, then check the furnace breaker in the main panel.
The front panel of the furnace also matters. A small push button behind the lower door cuts power whenever that door is off or not seated fully. If someone changed the filter and set the door back crooked, the furnace will not start. Press the door firmly into place.
Read the error light
Many furnaces have a small window in the lower door where you can see a light on the control board. A steady glow or a slow, even blink usually means normal. A pattern, such as three blinks then a pause, is a code. The chart that explains each code is commonly printed on a label inside the door panel or in the manual.
Write down the code before you turn anything off, since cutting power often clears it, and give it to the contractor when you call.
Gas supply and ignition
Find the shutoff valve on the gas pipe running into the furnace. The handle should line up with the pipe. If your stove or gas water heater also has no flame, the issue may be the supply to the house, which is a call for your gas company.
Modern furnaces light with an igniter rather than a standing pilot. If you hear the burners light and then shut off within seconds, a dirty flame sensor is a common cause. Igniters, flame sensors and gas valves are jobs for a licensed HVAC contractor. A dusty smell for a few minutes on the first cold day of the season is normal; a smell that keeps going, or smells like hot wiring, is not.
Heat pumps in very cold weather
If your home uses a heat pump, some behavior that looks like a problem is normal in very cold weather. The system runs for long stretches. The air from the vents feels lukewarm, warmer than the room but cooler than your hand. Several times a day the outdoor fan stops and the unit may give off steam while it runs a defrost cycle.
What is not normal: thick ice that covers the outdoor coil and stays, or a house that keeps losing temperature. Many heat pumps have backup electric heat, often labeled Emergency or EM Heat on the thermostat. Use that setting only to keep the house warm until a contractor looks at the heat pump.
Questions people ask
Who fixes furnaces in Maryland?
A licensed HVAC contractor. Maryland licenses them through the Maryland Board of Heating, Ventilation, Air Conditioning and Refrigeration Contractors, and you can look up a license on the board's website.
What should I do if the heat is out on a very cold night?
Open cabinet doors under sinks on outside walls since those pipes are at risk in the cold, and use space heaters only with plenty of clearance and never while asleep. Call for service as soon as you can.
Can I get a warning before the heat stops?
A smart thermostat can alert you when the indoor temperature drops below a set point. Strech, the home operating system, is being built to watch for that and line up a vetted local pro, with the price shown before work starts.
Related
Updated November 18, 2026 · Strech Inc., Montgomery County, Maryland