Sump pump not working: how to find the cause
A sump pump that is not working most often has lost power, has a float switch that is stuck, or is pushing water into a check valve or discharge line that is blocked. Many of these you can check in a few minutes with a bucket of water. If the pump hums but moves no water, or the pit keeps rising, call a licensed plumber.
If the pit is about to overflow
Keep away from the pit and any standing water if cords, outlets or appliances are wet. Turn off power at the panel only if you can reach it from a dry spot. If you have a wet rated vacuum or a spare utility pump, you can lower the water level while you sort out the main pump, as long as it is plugged into a dry outlet away from the water.
Always unplug the sump pump before you reach into the pit for any reason.
Check the power first
Power problems are the easiest fix and one of the most common.
- Make sure the plug is fully seated in the outlet.
- Many sump pumps plug into a GFCI outlet, the kind with test and reset buttons. Press reset firmly.
- Look for a tripped breaker at the panel.
- Some pumps use a piggyback plug, where the float switch plugs into the outlet and the pump plugs into the back of it. Make sure both are snug.
If the outlet keeps tripping as soon as the pump starts, the pump motor or its cord may be failing.
Test the float switch with a bucket
Slowly pour a bucket of water into the pit and watch. As the water rises, the float should lift and the pump should start, then shut off once the level drops.
- Float does not rise: it may be caught on the side of the pit, the pump body or its own cord. Unplug the pump, then free it.
- Float rises but nothing happens: the switch has likely failed.
- Pump runs and will not stop: the float may be stuck in the up position.
Also check that the pump sits level on a firm, clean base. Pumps that shift can trap their own float.
Pump runs but water does not leave
If you hear the motor but the water level barely drops, follow the water's path out.
- Check valve. This valve on the pipe above the pump stops water from falling back into the pit. If it is stuck shut or installed facing the wrong way, water cannot leave. If it fails open, water drains back and the pump cycles over and over.
- Intake and impeller. Gravel, silt or debris can clog the screen at the bottom of the pump.
- Discharge line. Outside, find where the pipe empties. Leaves, soil or a crushed section can block it. The outlet should send water well away from the foundation so it does not come right back.
If the pump runs nonstop even with a working float, it may be too small for the amount of water reaching the pit.
When to call a licensed plumber
Call a licensed plumber if the motor hums but will not pump, the pump trips the outlet, the switch is broken, the check valve needs replacing, or the pump is old and struggling. A plumber can also look at adding a battery backup or a second pump. If your pit has already overflowed, our guide on water in the basement covers what to do next.
Knowing before the pit overflows
A failed sump pump is usually silent, and you learn about it only when the floor is wet. A leak sensor or high water alarm placed beside the pit sends an alert as soon as the level climbs past where the pump should have started. A smart plug that tracks power use can also show when a pump runs far more than usual. Strech will link devices like these together, and when the pit starts rising it will send a vetted local plumber. You see the price before the work begins.
Questions people ask
Why is my sump pump running but not pumping water?
Most often a stuck or reversed check valve, a clogged intake screen, or a blocked discharge line. An impeller that has worn out can do the same.
Why does my sump pump keep turning on and off?
A check valve that leaks lets water fall back into the pit, so the pump keeps cycling. A float set too low can also cause short, frequent runs.
How do I test my sump pump?
Pour a bucket of water slowly into the pit. The float should rise, the pump should start, and the water should drop quickly before it shuts off.
Do I need a backup sump pump?
If your basement has finished space or your pump runs often, a battery backup is worth asking a plumber about, since the main pump cannot work during a power outage.
Related
Updated November 19, 2026 · Strech Inc., Montgomery County, Maryland