Leak under kitchen sink: how to trace it and fix it
A leak under the kitchen sink almost always comes from one of six spots: the supply lines, the shutoff valves, the drain trap, the garbage disposal, the base of the faucet or the dishwasher drain hose. Empty the cabinet, dry every part, and wrap each one in paper towel to see which gets wet first. Loose drain nuts and worn supply lines are often simple fixes, while a leaking valve or a cracked disposal needs more work.
Clear the cabinet and dry everything
Take everything out of the cabinet and put a towel or shallow pan on the floor of it. Turn on a light or use a flashlight. Then dry each pipe, valve and hose with a cloth, because a single damp surface hides where the water started.
If water is spraying or the leak is steady, close the two small shutoff valves under the sink by turning them clockwise. If they will not close, use the main water valve for the house.
The paper towel test
Wrap a dry strip of paper towel around each part below, or press a folded sheet under it. Then test one thing at a time so you know which action caused the water.
- Supply side first. With the faucet off, wait ten minutes. If paper on a supply line or valve gets wet, the leak is under pressure and happens all the time.
- Faucet next. Run the faucet for a minute with the drain open, then check the paper around the base of the faucet and under the sink deck.
- Drain last. Fill the sink a few inches, then pull the stopper so a rush of water goes down. Watch the trap, the slip nuts and the disposal.
- Dishwasher. Run a short cycle and check the hose where it connects to the disposal or the drain.
Water that only shows up when the sink drains points to the drain side. Water that shows up when nothing is running points to the supply side.
What you can tighten or replace
Drain trap and slip nuts. The curved trap and the pipes around it are held with large plastic or metal nuts. Hand tighten a loose nut, or a little more with pliers on metal. If it still drips, the plastic washer inside may be out of place or worn, and a new trap kit from a hardware store has all the parts.
Supply lines. These are the flexible hoses from the valves up to the faucet. A snug turn on the connection often stops a drip. If a line is kinked, rusty or bulging, replace it with one of the same length and fittings.
Dishwasher hose. A loose clamp at the disposal or drain is easy to tighten. The hose should rise in a high loop under the counter, or run to an air gap on the sink deck, so dirty water does not flow back into the dishwasher.
Leaks that need more than a wrench
- Shutoff valves that drip at the handle or will not close fully are often worn out, especially older multi turn valves.
- Faucet base leaks usually come from worn seals inside the faucet. Some can be rebuilt, others are easier to replace.
- Garbage disposal leaks from the body of the unit usually mean it is cracked inside. Leaks at the top flange or side connections can often be resealed. Our garbage disposal guide covers the unit itself.
- Wet wall or floor behind the cabinet with dry pipes means the leak may be inside the wall.
These are good reasons to call a licensed plumber. Replacing a valve means working on pipes that are always under pressure.
Where a cabinet leak sensor fits
A sink cabinet is closed most of the day, so a slow drip can soak the cabinet floor long before anyone sees it. A small leak sensor set flat on the cabinet floor, near the back where water collects, sends a phone alert at the first drop. Strech is the home operating system: it is being built to read sensors like this one and bring in a vetted local plumber, who shows the price before work starts.
Questions people ask
Why is there water under my sink but no visible leak?
Look for a slow drip that only happens when the sink drains or the dishwasher runs, a leak at the faucet base running down the pipes, or a leak inside the wall.
Can I use plumber's tape on a drain trap?
Usually not. Slip nuts seal with a plastic washer, not threads. Tape is meant for threaded pipe joints on the supply side.
How tight should the nuts under a sink be?
Plastic nuts should be hand tight plus a small turn. Overtightening can crack them and cause a new leak.
Is a small leak under the sink an emergency?
Usually not, but close the shutoff valves and keep a pan under it until it is fixed. Steady leaks from a supply line or valve should be repaired soon.
Related
Updated November 17, 2026 · Strech Inc., Montgomery County, Maryland