Garbage disposal not working: what the sound tells you
A garbage disposal that is not working usually either hums, which means the motor has power but the grinding plate is jammed, or stays silent, which means it has no power or its overload switch has tripped. Most jams clear with a hex key in the socket on the bottom of the unit, and most silent units start again after you press the red reset button. Always cut the power first and never put a hand inside.
Safety before anything else
Turn the wall switch off. Then either unplug the disposal from the outlet under the sink or switch off its breaker at the panel. A disposal can start the moment a jam frees, so the switch alone is not enough.
Never reach into the grinding chamber, even with the power off. To lift out a spoon, a bottle cap or a bone, use tongs or long pliers, and a flashlight to see. Keep the sink stopper nearby so nothing else falls in while you work.
If it hums but does not grind
Humming means the motor is trying to turn and something is holding the plate still.
- With the power off, look on the bottom center of the unit for a small six sided socket.
- Fit a hex key into it. Many units take a 1/4 inch key, and some come with a matching wrench, sometimes taped to the side. If yours is missing, check the size in the manual.
- Turn the key back and forth until it moves freely in a full circle.
- Remove whatever came loose with tongs, then restore power, run cold water and switch it on.
If it keeps humming after the plate turns freely, the motor may be failing.
If it is completely silent
Work through power in this order:
- Reset button. Most disposals have a small red button on the bottom. It pops out when the motor overheats. Let the unit cool for a few minutes, then press it firmly until it clicks.
- Switch and outlet. Some disposals are plugged into an outlet controlled by the wall switch. Check that the plug is fully seated. If the outlet has test and reset buttons, press reset.
- Breaker. Look for a tripped breaker at the panel and reset it once.
If the reset button keeps popping out, the unit is still jammed or overloaded. If the breaker trips again as soon as you switch it on, leave it off and call for help.
Water under the disposal
Dry the unit and run water to see where the drip forms.
- At the top, where it meets the sink: the sink flange seal has loosened. It can usually be resealed with plumber's putty.
- At the side, where the drain pipe or dishwasher hose connects: a gasket or clamp needs tightening or replacing.
- From the body or the bottom: the housing has cracked or the internal seals have worn through. The unit needs to be replaced.
A disposal that leaks from the bottom often drips slowly into a closed cabinet, and a small leak sensor on the cabinet floor can send an alert the first time water reaches it. For drips elsewhere in the cabinet, our guide to a leak under the kitchen sink walks through each spot.
Repair or replace
A disposal that still jams after you clear it, hums with a free plate, leaks from the body, or grinds slowly and loudly is near the end of its life. Replacing one is a common plumbing job, and because it involves both the drain and electrical power, a licensed plumber is a sensible choice if you are not comfortable with either. To help any disposal last, run cold water while it grinds and keep grease, large bones and stringy peels such as celery and corn husks out of it.
Questions people ask
Where is the reset button on a garbage disposal?
On most units it is a small red button on the bottom of the disposal, under the sink. Feel for it if you cannot see it.
Why does my garbage disposal hum but not work?
Something is jamming the grinding plate. Turn the power off and free it with a hex key in the socket on the bottom of the unit.
Can I use a drain cleaner in a garbage disposal?
It is better not to. Harsh chemicals can damage the unit and the seals. Clear jams by hand with the hex key instead.
Should I use hot or cold water with a disposal?
Cold. It keeps grease firm so the disposal can chop it up and move it on, rather than letting it coat the pipes.
Related
Updated November 17, 2026 · Strech Inc., Montgomery County, Maryland