Low water pressure: one fixture or the whole house
Low water pressure at a single faucet or shower is usually a clogged aerator, showerhead or cartridge, which you can often clean yourself. Low water pressure in the whole house more often comes from a main valve that is not fully open, a failing pressure reducing valve, a hidden leak, or old galvanized pipes narrowed by rust inside. The first step is to figure out which of those two situations you have.
One fixture or the whole house?
Turn on the cold water at a few sinks, a shower and an outdoor spigot, one at a time.
- Only one faucet or shower is weak: the cause is almost always at that fixture.
- Only the hot water is weak, everywhere: look at the water heater, where a partly closed valve or sediment can restrict flow.
- Everything is weak: the cause is on the main line, at the pressure reducing valve, in the pipes, or with the water supply itself.
Ask a neighbor whether their pressure dropped too. If it did, the utility may be working on a main nearby.
Fixing a single weak fixture
- Faucet aerator. Unscrew the small screen at the tip of the spout. Rinse out grit and soak it in white vinegar to loosen mineral buildup, then screw it back on.
- Showerhead. Mineral deposits block the small holes. Soak the head in vinegar or replace it.
- Shutoff valves. Check that the small valves under the sink are fully open. They are sometimes left half closed after other work.
- Cartridge. If the aerator is clean and the flow is still weak, the cartridge inside a single handle faucet may be clogged or worn.
Pressure that fell right after plumbing work often means debris came loose and lodged in an aerator or valve.
Checking the whole house
- Main shutoff valve. Find it where the water line enters, often on a front basement wall. Make sure it is fully open.
- Pressure reducing valve. Many homes have a bell shaped pressure reducing valve, or PRV, on the main line just after the shutoff. When these wear out, house pressure can drop or swing. A plumber can test and adjust or replace it.
- Measure it. A simple pressure gauge from a hardware store screws onto an outdoor spigot. Many homes run somewhere between about 40 and 80 psi. A reading well under 40 helps explain weak flow.
- Rule out a leak. With all water off, see whether your meter still moves. Water escaping underground lowers pressure and raises your bill. Our WSSC water bill guide shows how to read it.
Galvanized pipes in older homes
Homes built before about 1960 often have galvanized steel supply pipes. Over decades, rust builds up inside them and slowly narrows the opening, so pressure falls a little every year and often gets worse on upper floors. Brown or rusty water when a tap first opens is another sign.
Cleaning will not fix this. The answer is replacing those runs with copper or PEX, which a plumber can often do in sections, starting with the worst lines.
When pressure trouble needs a plumber
Call a licensed plumber if the whole house is weak and the main valve is open, if your gauge reads low, if the pressure reducing valve is old or pressure swings up and down, if you see rusty water, or if the meter shows a leak you cannot find. Leave adjusting or replacing the PRV to a pro, since setting it too high can strain pipes, the water heater and appliances.
Seeing pressure trends sooner
Pressure changes are hard to notice when they happen slowly. Some smart water shutoff valves track pressure and flow on the main line and send an alert when either one shifts, which can also reveal a hidden leak. Strech will bring readings like these into one place, flag a slow slide in pressure, and send a vetted local plumber with the price up front, before any work starts.
Questions people ask
Why is my water pressure low all of a sudden?
A sudden drop across the whole house often means a partly closed valve, a failing pressure reducing valve, a leak, or utility work nearby. Check with a neighbor first.
Why is the water pressure low in only one bathroom?
Look at that room's aerators, showerhead and shutoff valves. If they are clear, a narrowed pipe feeding that bathroom may be the cause.
Where is my pressure reducing valve?
It is usually on the main water line just after the main shutoff valve, often in the basement. Some homes do not have one.
Can old pipes cause low water pressure?
Yes. Galvanized steel pipes, common in homes built before about 1960, collect rust inside and lose flow over time.
Related
Updated November 19, 2026 · Strech Inc., Montgomery County, Maryland